タグ:ドウカティ

5
sketch-1537021446195
フジミ フェラーリ 458 イタリアを製作しています
Fujimi Ferrari 458 I am producing Italy




ナックル部分(アップライト)をセミグロスブラックに
説明書通りなんですが
ナックル部分(アップライト)はアルミなのでは?とも思いますが……
Knuckle part (upright) to semi-gross black
It is as per instructions
Is the knuckle part (upright) aluminum? I think that, though.
DSC_7713




キャリパーの刻印は削り落としてますので(塗るのは不可能に近い)
デカールを貼ります
フェラーリのキャリパーの文字には向きが有りますので
タミヤのFXXKの説明書を見ながら貼ってます
Fの文字が上に来るのだったと思います
I cut off the stamp of the caliper (it is near impossible to paint)
I will paste the decal
Since the character of the Ferrari caliper is oriented
I am sticking it while watching the instructions of Tamiya's FXXK
I think that the character of F came upward
DSC_7718




デカールが乾いたらクリアーコートします
When the decal dries it will clear coat
DSC_7719





ホイールはグロスブラックにしてます
一回グロスブラックを吹きました
もう一度この上からブラックを吹きます
The wheel is gross black.
I blew Gross Black once
I will blow black again from above
DSC_7714




グロスの黒を2回吹いてクリアーコート
Clear coat blowing black of gloss twice
DSC_7724




あ!デカール忘れてる(゜ロ゜;ノ)ノ
クリアーが完全に乾いてからデカール貼ります(^_^;)))
Ah! I forgot the decal (゜ ロ; ノ) ノ
I will stick the decal after clearing completely dry (^ _ ^;)))
DSC_7727




キャリパーもクリアーコート
黄色を吹いた時は艶が落ちてましたが
クリアー吹いて光ってるのでOKですね
The caliper also clear coat
Gloss faded when I blew yellow
It's ok so it's clear and blowing and shining
DSC_7726


このエントリーをはてなブックマークに追加 mixiチェック

5
sketch-1537021446195
フジミ フェラーリ 458 イタリアを製作しています
Fujimi Ferrari 458 I am producing Italy






新しいハイターにキャリパーを入れてます
すぐにメッキが落ちますね
ホイールの時と大違いです(^_^;)))
I put a caliper in the new highter
Plating will fall shortly
It is very different from the time of wheel (^ _ ^;)))
DSC_7705





アップライトにキャリパーの外側を接着して
白サフを吹いて黄色を吹いてます
クレオスのスタンダードイエローに蛍光イエローを少したしてます
Adhere the outside of the caliper to the upright
I blow a white suff and blow yellow.
I give a few fluorescent yellow to Creos' standard yellow
DSC_7706





line_1537621436296





タペットカバー(シリンダーヘッドカバー)とサージタンクはガイアのサンシャインレッドを砂吹きで
Tappet cover (cylinder head cover) and surge tank blow sunshine red of Gaia
DSC_7708




ホイールは黒サフ状態です
シルバーにするか?グロスブラックにするか?思案中です
Wheel is black suffocate
Would you like silver? Would you like to gross black? I'm thinking
DSC_7709




このエントリーをはてなブックマークに追加 mixiチェック

5
sketch-1537021446195
フジミ フェラーリ 458 イタリアを製作しています
Fujimi Ferrari 458 I am producing Italy





この説明書ではタイヤの種類とか記載されてますがタイヤの向きが判りませんよね………(゜ロ゜;ノ)ノ
In this manual, although the type of the tire is described, the direction of the tire is not understood ......... (゜ ロ °; ノ) ノ
DSC_7677




ホイールはメッキを落としてます
ハイター使い古しなので落ちが悪い(^_^;)))
Wheel is dropping plating
Because it is a heater worn-out, I feel bad (^ _ ^;)))
DSC_7678




ボディーにサイドスカート部分とリアのバンパーを取り付け
裏から補強のプラ板を当ててます
Attach side skirt part and rear bumper to body
I am applying a reinforced plastic plate from the back
DSC_7681




DSC_7682




助手席側のキーボタン?
(シリンダーは使われてない)
無いのかな?
無ければ埋めなければ
(アウタードアハンドルは有ります)
Key button on the passenger side?
(Cylinder is not used)
Is not there?
If it does not fill it up
(There is an outer door handle)
DSC_7683





落ちが悪かったですが
引き上げました
使い古しハイターはダメですね(^_^;)))
It was bad
I raised it.
Worn-out highter is not good (^ _ ^;)))
DSC_7691




ウインカーのランプを切り飛ばし
印の穴を
ドアの所にも穴を
I cut off the lamp of the turn signal
The hole of the mark
Also a hole at the door
DSC_7696




ドアミラーに真鍮線を
Brass wire to the door mirror
DSC_7695


このエントリーをはてなブックマークに追加 mixiチェック

5
sketch-1537021446195
フジミ フェラーリ 458 イタリアを製作しています
Fujimi Ferrari 458 I am producing Italy






後ろのディスクローターの凹みが裸眼では判らないですね
拡大鏡ごしに作業してます
これは穴を開けるか深くしとかないと塗装で確実に埋まってしまいますね
I can not understand the concavity of the disc rotor in the rear by the naked eye
I am working on a magnifying glass.
This will surely be filled with paint if you do not open or deepen it
DSC_7663





ディスクローターはグラファイトブラックを塗りました
黒いのと比べないと判りませんね(;´∀`)
クリアーを吹くと違いが判るのですが
ディスクローターは艶無しですからね
ホイールの中では黒にしか見てませんよね
もう少し明るめに変更するかな?
Disk rotor painted graphite black
I do not know without compare it with black (; '∀ `)
When you blow clear, you can see the difference
Because the disk rotor is not glossy
I only saw it in black in the wheel
What?
Would you like to change it a little more?
DSC_7667




室内黒にします
シックにいきます(^_^)
I will indoor black
I will go to chic (^ _ ^)
DSC_7668





左側少し明るいと思います
自作カーボン色です
グラファイトブラックよりメタリックの粒子が多いですね
ホイールの中だとこれぐらいで良いかも?
I think that it is a little bright on the left side
It is a self-made carbon color
There are many metallic particles than graphite black
It might be good if this is in the wheel?
DSC_7670



シルバーでタッチアップ
ここの名称を忘れました………
あ!最初から名前を知らない………
普通のディスクローターだと無いですからね(^_^;)))
Touch up with silver
I forgot the name here .........
Ah! I do not know the name from the beginning .........
Because it is not an ordinary disk rotor (^ _ ^;)))
DSC_7673



このエントリーをはてなブックマークに追加 mixiチェック

5
sketch-1535549363053
AJINOMOTO ホンダ NSR 250  '90を製作しています
AJINOMOTO Honda NSR 250 '90 is being produced





残りは組むだけですので
The rest is just a bra
DSC_7765




DSC_7766




DSC_7767




これで完成になります
This will be completed
DSC_7768




DSC_7769




DSC_7770




DSC_7771



DSC_7772



DSC_7773




DSC_7774

基本ストレート組
ディスクローターの穴を開けたぐらいですね
デカールがカルトグラフなので大丈夫だろうとクリアーコートを急いだら(;>_<;)
急いては事を仕損じるですね(;´∀`)
やり直しはせずに
今後の教訓にそのまま完成させました
このブルーとグリーンは塗装で仕上げた方が良いと思いますね
Basic straight pair
It is about the hole of the disk rotor
Since the decal is a cult chart, I hurry if I hurry up the clear coat (;> _ <;)
I hurry things in a hurry (; '∀ `)
Without redoing
I completed the lesson learned as it is
I think that it is better to finish this blue and green with paint




プラモデル製作に復帰して4台目のバイクでしたが
バイクは難しいですね(;´∀`)
It was the fourth motorcycle after returning to the plastic model production
Bike is difficult, is not it (; '∀ `)




こちらは過去に製作したバイクです
タミヤの1/6モンキーをCBXカラーに
This is a bike I made in the past
Tamiya's 1/6 Monkey to CBX color
DSC_1466




タミヤ1/12ドウカティ
Tamiya 1/12 Dowati
DSC_3374



タミヤ1/12ドウカティ
Tamiya 1/12 Dowati
DSC_3702




次はカーモデルに戻ります(^_^)
赤が似合う車だとだけ………\(^o^)/

Next will return to the car model (^ _ ^)
Only with red cars ......... \ (^ o ^) /




このエントリーをはてなブックマークに追加 mixiチェック

↑このページのトップヘ