タグ:スーパーカー

5
sketch-1550879473290
フジミ 1/24 フェラーリ F-40 TOTIPを製作しています
We are manufacturing Fujimi 1/24 Ferrari F-40 TOTIP




line_1553172647953




フロントガラスのボカシです
It is Bokashi of the windshield
DSC_0015




DSC_0019



ボディーに仮に
Temporarily in the body
DSC_0020




室内が付くと暗くなりますね
It becomes dark when the room is attached
DSC_0021




ランプの取り付け
Lamp installation
DSC_0025




裏側にはラピテープを貼ってタミヤのクラフトボンドで剥がれ防止してます
I put a lapi tape on the back side to prevent peeling with Tamiya Craft Bond.
DSC_0026




フロントのメッシュ
瞬間で着けてます
Front mesh
I can wear it in a moment
DSC_0027




後ろのメッシュも同じく瞬間です
The mesh behind is also a moment
DSC_0028




リアウイングが有るのでメッシュが有るのは判りにくいですが(((^_^;)
Because there is a rear wing, it is hard to know that there is a mesh (((^ _ ^;)
DSC_0029





アメブロ時代の記事を手作業で移してます
コピー&張り付けで時間は掛かってます
それゆえに製作の方もいつもより遅くなってます
現時点ではランボルギーニ ミウラの記事が30

Screenshot_20190418-232924




フェラーリ365GT4BBの記事が4つぐらい?
BBの方は終わりからになってます(((^_^;)
Screenshot_20190418-232951


BBの方は最近に近いので今と変わりは無いのですがミウラの方は製作に復帰してすぐの頃で
ハチャメチャな事も多いですね(((^_^;)
復帰して試行錯誤してた頃なので仕方無いと言えばそうなんですが………


カテゴリーから検索して頂ければ見れると思います





このエントリーをはてなブックマークに追加 mixiチェック

5
sketch-1550879473290
フジミ 1/24 フェラーリ F-40 TOTIPを製作しています
We are manufacturing Fujimi 1/24 Ferrari F-40 TOTIP




テールランプの塗り分け
少し面倒ですね
Differently painted tail lamps
It is a little troublesome
DSC_9853





バックランプの所は透明だと思います(説明書ではH2なので白の指定ですかね?)
マスキングゾルでマスキングします
マスキングゾルに付いてる筆では太すぎますので
ネイルのシリコンペンで塗るようにしてます
I think that the place of the back lamp is transparent (in the manual, it is H2 because it is H2?)
Mask with masking sol
Because the brush attached to the masking sol is too thick
I try to paint with silicone pen of nails
DSC_9854




金属メッシュが付属してるのは嬉しいのですが
エッチングバサミの登場ですね
I'm glad that the metal mesh is included
It is appearance of etching scissors
DSC_9855





切り出してる途中の写真は有りませんが
エッチングバサミで地道に切りました
説明書通りに両面テープを使って型紙を貼り
型紙ごと切ってます
There are no photos in the process of being cut out
I cut it steady with etching scissors
Apply the template using double-sided tape as per the instructions
I cut the whole pattern
DSC_9856




リアのメッシュはテールランプ等と取り付けが有るので大変ですね(;´∀`)
The rear mesh has a tail lamp etc. and is attached, so it is difficult (; ∀ `)
DSC_9857




サイドのガラス
ボディー色に塗った所が有りましたが
説明書通りでは足りませんね
Side glass
There was a place I painted in the body color
It is not enough according to the manual
DSC_9858




実際はここまで塗る必要が有りますね
In fact, it is necessary to paint this far
DSC_9859




308や328ではここは完全にガラスですがF-40は導風口になってるんです
Here is completely glass in 308 and 328, but F-40 has become a vent.
DSC_9860





このエントリーをはてなブックマークに追加 mixiチェック

5
sketch-1550879473290
フジミ 1/24 フェラーリ F-40 TOTIPを製作しています
We are manufacturing Fujimi 1/24 Ferrari F-40 TOTIP





前回付く所が判らなかったロッドですが
タミヤのF-40ではボディーに付くようになってますね(正確にはボディーと違うかも?)
室内を固定してます
It is a rod I did not know where to stick last time
Tamiya's F-40 is attached to the body (it may be different from the body?)
I have fixed the room
DSC_9846




タイヤも付けてボディーを仮に載せてみました
I tried to put on the body temporarily with the tires
DSC_9847




タミヤの場合はリアカウルが開くのでロッドをボディーの裏に接着は可能ですが
フジミの場合リアカウルは固定なので………
ロッドは室内とエンジニアルームの隔壁の一番上の所に接着しました(((^_^;)
In the case of Tamiya, the rear cowl opens, so it is possible to bond the rod to the back of the body
In the case of Fujimi, the rear cowl is fixed .........
The rod was glued to the top of the partition in the room and the engineer room (((^ _ ^;)
DSC_9848





まだ仮にボディーを載せてるだけですが
F-40はカッコ良いですね
I still only temporarily put the body
F-40 is cool
DSC_9849




ボディーはデカール貼りですが
使うのはフェラーリのエンブレムぐらいですね
Although the body is decals
It is about the emblem of Ferrari to use
DSC_9850




シャシーはラジエターも付けたので終わりですね
The chassis also attached a radiator so it's over
DSC_9851





白のボディーに黄色のエンブレムは目立ちますね
The yellow emblem stands out on the white body
DSC_9852




このエントリーをはてなブックマークに追加 mixiチェック

5
Screenshot_20190413-233411



Screenshot_20190413-233434


今週は一万歩を超える日も有りました(^_^)

娘が小学校を卒業してからも
私は朝のウォーキングは続いてます
今週の水曜火が中学の入学式だったのですが
中学は小学校の登校時間より少しは遅いので
私は一人で寂しくですね(((^_^;)


ちなみに今朝は朝寝坊(;´∀`)
7時に起きてトイレに行ったのですが………
その後布団に戻ってしまった(゜ロ゜;ノ)ノ





このエントリーをはてなブックマークに追加 mixiチェック

5
sketch-1550879473290
フジミ 1/24 フェラーリ F-40 TOTIPを製作しています
We are manufacturing Fujimi 1/24 Ferrari F-40 TOTIP




シリンダーヘッドカバー(タペットカバー)を塗るためのマスキング
Masking for painting the cylinder head cover (tappet cover)
DSC_9765





キャリパーの色が乾燥しましたので取り付け
Since the color of the caliper was dry, install it
DSC_9766





シートの座面を塗る為のマスキング
Masking to paint the seat surface
DSC_9768




タイヤのパーティングラインの処理
箱車でリアカウルが開いたりしないのでタイヤの見える率は低いのでそのままでも良いのですが、タイヤがスリックなので
ペーパー掛けしてます
上が未処理
下が処理後
Processing of tire parting line
As the rear cowl does not open in a box car, the visibility rate of the tires is low, so it is fine, but the tires are slick
I'm hanging on paper
Top is unprocessed
Lower is after processing
DSC_9769




DSC_9770




仮にホイールやタイヤを付けてみて
延長パイプを接着してます
Temporarily put on wheels and tires
I glue the extension pipe
DSC_9771




今日は娘の中学の入学式で
仕事を休んで行きましたが
寒かったですね(;´∀`)
小学校の卒業式の時も寒かったですね(;´∀`)
コート着用でも寒いし(;>_<;)
sketch-1554864650810




sketch-1554866741835






このエントリーをはてなブックマークに追加 mixiチェック

↑このページのトップヘ