模型製作・車の修理・ロレックス等
プラモデルはフェラーリをメインに製作してます
月刊ホビージャパン誌でカーモデルの作例を担当する時も有ります
自動車整備士の経験を生かした製作する時も
作例製作中はblogは不定期更新になります

カテゴリ: フジミ フェラーリ F-430 チャレンジ クランベリー レッド パール

5
sketch-1549883784420
フジミ フェラーリF-430 チャレンジを製作していま
We are producing the Fujimi Ferrari F-430 Challenge






結局車名プレートは付けずに完成写真を(((^_^;)
After all, without the car name plate attached (((^ _ ^;) completed photo
DSC_9828




DSC_9829




DSC_9830




DSC_9831




DSC_9832




DSC_9833





DSC_9834





昔作った偏光パールのF-430チャレンジと一緒に
Together with the Polarized Pearl F-430 Challenge
DSC_9835





昔作ったのはstudio27のエッチングを使ってます
I used to etch the studio27 that I made long ago
DSC_9836




DSC_9837




DSC_9838






写真では色が少し明るくなってる気がしますので
ディノ246GTも並べてみました
I feel the color is a little brighter in the photo
I also ordered Dino 246 GT
DSC_9839







ランキングに参加しています
ポチッと宜しくお願いします(^-^)v

5
sketch-1549883784420
フジミ フェラーリF-430 チャレンジを製作しています
We are producing the Fujimi Ferrari F-430 Challenge






フロントガラスとリアガラスはエポキシで固定
ドアミラーもエポキシですね
Fix the windshield and rear glass with epoxy
The door mirror is also epoxy
DSC_9822





ウィンカーはインセクトピンの頭をクリアーオレンジで塗ってます
The blinker is painting the head of the insect pin with clear orange
DSC_9824





シャシーと合体しました
F-430系はボディーとシャシーの合いが後部が悪い時が有るのですが
この固体は大丈夫ですね
ボディーやシャシーが少し歪んでると思ったのですが………
ボディーをIPAにドボンしたのが良かったりして?(((^_^;)
I united with the chassis
In the F-430 series, there are times when the rear of the body and chassis is bad
This solid is ok
I thought that the body and chassis were a bit distorted .........
Is it good to have a body deboned to IPA? (((^ _ ^;)
DSC_9825





接着も覚悟してましたが
バッチリですね
I was prepared for adhesion
It is batchy
DSC_9826





次回完成です
ナンバープレート(車名プレート)のデカールが浮いちゃって
マークセッターを塗ってます(((^_^;)
It is completed next time
Decals on the license plate (car name plate) have floated
I'm painting a mark setter (((^ _ ^;)
DSC_9827











ランキングに参加しています
ポチッと宜しくお願いします(^-^)v

5
sketch-1549883784420
フジミ フェラーリF-430 チャレンジを製作しています
We are producing the Fujimi Ferrari F-430 Challenge






少し軟らかい感触が有ったのでもう2〜3日放置してから磨きました
I had a little soft feel, so I left for another 2-3 days
DSC_9801




磨いてからも2〜3日放置してからマスキングしてます
I leave it for 2 to 3 days after polishing and then mask it
DSC_9810




塗り終わりすぐにマスキングを剥がしてます
I finish removing the masking immediately after the application
DSC_9816




同時に中も塗ってます
I am also painting inside
DSC_9817





ルームミラーの取り付け
エポキシです
ミラーの付く面を先に黒に塗ってます
Mounting the room mirror
It is an epoxy
I painted the mirror side black first
DSC_9819





ミラー面にはハセガワのミラーフィニッシュを貼ってますが
ヒケが凄くて修正するのも大変なのでスルーしてます(;´∀`)
I put a mirror finish of Hasegawa on the mirror surface
I'm going through it because it's hard to fix the sink marks and it's difficult (;; ∀`)
DSC_9820




ライトのレンズ
少し周囲を削らないと入りそうに無いですね
Light lens
It is not likely to enter without cutting around a little
DSC_9821





縁を少し削るぐらいで入りました
I cut in the edge a little
DSC_9823





急遽部屋の模様替えをする事に
家のインターネット回線を変更する事にした為で
今はeo光を使ってますがドコモ光へ変更です
eo光に不満は無かったのですが
ドコモ光だとスマホとの割引も有りますので
まずは作業机の下から片付けを………
机の配置変更
パソコンの移動
私のメイン使いのノートパソコン1台は娘へ
私はデスクトップ1台になります
デスクトップの方はプリンターやスキャナー繋いで無いのでソフトのインストールもたくさんせねば(゜ロ゜;ノ)ノ
To change the room suddenly
Because I decided to change my house's internet connection
We use eo light now, but it is change to docomo light
There was no dissatisfaction with eo light
As there is discount with smartphone when it is docomo light
At first we tidy up from under work desk .........
Desk layout change
PC movement
One of my main laptops to my daughter
I will be one desktop
Since there is no printer or scanner connection on the desktop, you have to install a lot of software (;;; ノ)
DSC_0132




blogは保存記事のアップですが
今製作中のキット………
待避してもらいます
blog is up of preservation article, but
Kit currently being produced .........
I will get back
DSC_0133




Nゲージのジオラマの下も待避場所になりますね
It will be a retreat place under the N gauge diorama too
DSC_0134




ランキングに参加しています
ポチッと宜しくお願いします(^-^)v

5
sketch-1549883784420
フジミ フェラーリF-430 チャレンジを製作しています
We are producing the Fujimi Ferrari F-430 Challenge





前回のクリアーから1週間
中研ぎをしまして
オーバーコートしてます
1 week since last clear
Do your best
I do overcoat
DSC_9779




DSC_9780




DSC_9781




また1週間ぐらい乾燥させます
I will dry it for another week
DSC_9787





天井を軽く磨いて様子見です
スポンジヤスリの行程は省きました
ラプロスの6000番からスタートしてます
1週間過ぎてますが
まだ軟らかいような気もしますね
I lightly polish the ceiling and watch it
I have omitted the process of sponge file
We have started from Lapros 6000
It has been over a week
I feel like it is still soft
DSC_9797






アメリカレベル アウディ R8 1/24 4211 プラモデル
アメリカレベル(America Revell)
2010-07-15


5
sketch-1549883784420
フジミ フェラーリF-430 チャレンジを製作しています
We are producing the Fujimi Ferrari F-430 Challenge





エッチング等を使いませんので
デカールを貼ります
貼るのはエンブレム等だけです
As we do not use etching
Paste the decal
It is only emblems to put
DSC_9721




DSC_9722




DSC_9723




簡単に砂吹きして
Sandblasting easily
DSC_9724




クリアーを吹きました
Blew the clear
DSC_9725




しばらく乾燥させます
Let dry for a while
DSC_9726






↑このページのトップヘ