2019年04月

5
sketch-1550879473290
フジミ 1/24 フェラーリ F-40 TOTIPを製作しています
We are manufacturing Fujimi 1/24 Ferrari F-40 TOTIP





ガイアのアルティメットホワイトからスタートです
Start from Gaia's Ultimate White
line_1551963900178





DSC_9799




DSC_9800




DSC_9802




DSC_9803




DSC_9804




DSC_9805
最終はクレオスのクリスタルカラーのサファイアブルーを吹きましたが………
クレオスのクリスタルカラーは黄色味が出ますよね(;´∀`)
どうするかな?(;´∀`)
The last blows sapphire blue in Creos crystal color ...
Creos crystal color is yellowish (;; `)
What should I do? (; ∀ `)





シートは赤でベルトは黒に
The seat is red and the belt is black
DSC_9807




クリアーパーツをマスキングして塗りますが
キットが古いのでマスキングシールは有りませんので自分でします
I will mask and paint clear parts
Since the kit is old, there is no masking seal, so I do it myself
DSC_9808





サイドガラスの一部をボディー色に塗る必要が有るのでマスキング
ここは簡単に済みますね
Masking because it is necessary to paint a part of the side glass in the body color
This is easy to do
DSC_9811



このエントリーをはてなブックマークに追加 mixiチェック

5
sketch-1550879473290
フジミ 1/24 フェラーリ F-40 TOTIPを製作しています
We are manufacturing Fujimi 1/24 Ferrari F-40 TOTIP





メーターのデカールはプラ板に貼りました
The decals of the meter were attached to the plastic board
DSC_9788




なぜかと言うとノーマルF-40のメーターと違うんですよね(((^_^;)
Why is it different from the normal F-40 meter (((^ _ ^;)
DSC_9789




グレーだと筋掘りもしやすいですね
脱線が減ります
It is easy to do muscle digging if it is gray
Derailment is reduced
DSC_9790




DSC_9791




フューエルリッドのモールドが甘過ぎるので彫ってます
6ミリで合いますね
I carve because the mold of the fuel lid is too sweet
It fits in 6 mm
DSC_9792




捨てサフを研ぎましたが
ダクトの中までは無理ですね(((^_^;)
I sharpened the abandoned saf
It is impossible until the inside of the duct (((^ _ ^;)
DSC_9793




本サフ
クレオスの1500番グレーです
This saf
It is gray 1500 of Creos
DSC_9794




マフラーエンドはnextを吹いてます
The muffler end is blowing next
DSC_9795




DSC_9796








このエントリーをはてなブックマークに追加 mixiチェック

5
sketch-1550879473290
フジミ 1/24 フェラーリ F-40 TOTIPを製作しています
We are manufacturing Fujimi 1/24 Ferrari F-40 TOTIP





F-40のボディ比べ(((^_^;)
Body comparison of F-40 (((^ _ ^;)
DSC_9773




タミヤの方が全長特にフロントカウルが長いたいですね
I want Tamiya to have a longer overall length, especially the front cowl.
DSC_9774





リアカウルサイドのスリットも違いますね
4本
The slit of rear cover is also different
4 bottles
DSC_9775





フジミは5本
Five Fujimi
DSC_9776





フジミのLMも5本
Also five LM of Fujimi
DSC_9777





LMはフェンダーが張り出した専用ボディですね
LM is a dedicated body with a fender overhang
DSC_9778





ホイールは艶黒にしてます
DSC_9782




DSC_9783




筋掘りをするにも白では判りにくくて
最近は合わせ目のチェックぐらいしか捨てサフは吹かないようにしてるのですが
吹いてます
It is difficult to understand in white even when digging
Recently, I'm trying to throw off only the check on the seam but not to blow the saf
I'm blowing
DSC_9784





このエントリーをはてなブックマークに追加 mixiチェック

5
sketch-1550879473290
フジミ 1/24 フェラーリ F-40 TOTIPを製作しています
We are manufacturing Fujimi 1/24 Ferrari F-40 TOTIP




シリンダーヘッドカバー(タペットカバー)を塗るためのマスキング
Masking for painting the cylinder head cover (tappet cover)
DSC_9765





キャリパーの色が乾燥しましたので取り付け
Since the color of the caliper was dry, install it
DSC_9766





シートの座面を塗る為のマスキング
Masking to paint the seat surface
DSC_9768




タイヤのパーティングラインの処理
箱車でリアカウルが開いたりしないのでタイヤの見える率は低いのでそのままでも良いのですが、タイヤがスリックなので
ペーパー掛けしてます
上が未処理
下が処理後
Processing of tire parting line
As the rear cowl does not open in a box car, the visibility rate of the tires is low, so it is fine, but the tires are slick
I'm hanging on paper
Top is unprocessed
Lower is after processing
DSC_9769




DSC_9770




仮にホイールやタイヤを付けてみて
延長パイプを接着してます
Temporarily put on wheels and tires
I glue the extension pipe
DSC_9771




今日は娘の中学の入学式で
仕事を休んで行きましたが
寒かったですね(;´∀`)
小学校の卒業式の時も寒かったですね(;´∀`)
コート着用でも寒いし(;>_<;)
sketch-1554864650810




sketch-1554866741835






このエントリーをはてなブックマークに追加 mixiチェック

5
sketch-1550879473290
フジミ 1/24 フェラーリ F-40 TOTIPを製作しています
We are manufacturing Fujimi 1/24 Ferrari F-40 TOTIP





前回よりもう少しマスキングして
Mask a bit more than last time
DSC_9758





黒鉄色にラフゴールドを混ぜた色を吹いてます
その後スモークグレーにフラットベースを混ぜて艶を落としたのを吹いてます
I am blowing a color mixed with rough gold in black iron color
Then I mix it with smoked gray and mix it with a flat base to blow it off.
DSC_9763





シートの背面も同様にですが艶は落としてません
The back of the sheet is the same but the luster is not lost
DSC_9764





キャリパーはクレオスのGXメタルレッド
Caliper is Creos GX metal red
DSC_9759





少し明るいですがホイールの中になれば少しは暗く見えるかなと
ホイールは艶黒ですね
It's a bit bright, but if it's in the wheel it will look a bit dark
The wheel is glossy black
DSC_9760




エアクリーナーとオイルクーラーですが
シルバーからセミグロスブラックに変更です
It is an air cleaner and an oil cooler
Change from silver to semi-gloss black
DSC_9761





マフラーやウエストゲートに少しですが焼けの表現を追加
Add a bit of a burnt expression to the muffler or Westgate
DSC_9762



このエントリーをはてなブックマークに追加 mixiチェック

↑このページのトップヘ