2019年04月

5
sketch-1550879473290
フジミ 1/24 フェラーリ F-40 TOTIPを製作しています
We are manufacturing Fujimi 1/24 Ferrari F-40 TOTIP




昼の短時間の間に
クリアーの砂吹きと言ってもエンブレムだけなので普通に吹いてます
埃が数個入ってるので軽く中研ぎして
クリアーを重ねて行きます
Within a short time of day
Even if it is clear sandblasting, it is only an emblem so it blows normally
Since some dust is contained, lightly grind the inside
I will go over the clear
DSC_9861




テールランプ
まずはクリアーオレンジ
乾燥後にマスキングして
クリアーレッドになります
夜にはクリアーレッドを吹けると思います
tail lamp
At first clear orange
Mask after drying
It becomes clear red
I think I can blow clear red at night
DSC_9862




夜にクリアーレッドを塗りました
I painted a clear red at night
DSC_9866




ボディーにもクリアーを
Clear to the body
DSC_9863




DSC_9864




DSC_9865




ガラスにはボディー色を
Glass body color
DSC_9867




切り出したメッシュにはメタルプライマーを
Use a metal primer on the cut mesh
DSC_9868




このエントリーをはてなブックマークに追加 mixiチェック

5
sketch-1550879473290
フジミ 1/24 フェラーリ F-40 TOTIPを製作しています
We are manufacturing Fujimi 1/24 Ferrari F-40 TOTIP




テールランプの塗り分け
少し面倒ですね
Differently painted tail lamps
It is a little troublesome
DSC_9853





バックランプの所は透明だと思います(説明書ではH2なので白の指定ですかね?)
マスキングゾルでマスキングします
マスキングゾルに付いてる筆では太すぎますので
ネイルのシリコンペンで塗るようにしてます
I think that the place of the back lamp is transparent (in the manual, it is H2 because it is H2?)
Mask with masking sol
Because the brush attached to the masking sol is too thick
I try to paint with silicone pen of nails
DSC_9854




金属メッシュが付属してるのは嬉しいのですが
エッチングバサミの登場ですね
I'm glad that the metal mesh is included
It is appearance of etching scissors
DSC_9855





切り出してる途中の写真は有りませんが
エッチングバサミで地道に切りました
説明書通りに両面テープを使って型紙を貼り
型紙ごと切ってます
There are no photos in the process of being cut out
I cut it steady with etching scissors
Apply the template using double-sided tape as per the instructions
I cut the whole pattern
DSC_9856




リアのメッシュはテールランプ等と取り付けが有るので大変ですね(;´∀`)
The rear mesh has a tail lamp etc. and is attached, so it is difficult (; ∀ `)
DSC_9857




サイドのガラス
ボディー色に塗った所が有りましたが
説明書通りでは足りませんね
Side glass
There was a place I painted in the body color
It is not enough according to the manual
DSC_9858




実際はここまで塗る必要が有りますね
In fact, it is necessary to paint this far
DSC_9859




308や328ではここは完全にガラスですがF-40は導風口になってるんです
Here is completely glass in 308 and 328, but F-40 has become a vent.
DSC_9860





このエントリーをはてなブックマークに追加 mixiチェック

5
sketch-1550879473290
フジミ 1/24 フェラーリ F-40 TOTIPを製作しています
We are manufacturing Fujimi 1/24 Ferrari F-40 TOTIP





前回付く所が判らなかったロッドですが
タミヤのF-40ではボディーに付くようになってますね(正確にはボディーと違うかも?)
室内を固定してます
It is a rod I did not know where to stick last time
Tamiya's F-40 is attached to the body (it may be different from the body?)
I have fixed the room
DSC_9846




タイヤも付けてボディーを仮に載せてみました
I tried to put on the body temporarily with the tires
DSC_9847




タミヤの場合はリアカウルが開くのでロッドをボディーの裏に接着は可能ですが
フジミの場合リアカウルは固定なので………
ロッドは室内とエンジニアルームの隔壁の一番上の所に接着しました(((^_^;)
In the case of Tamiya, the rear cowl opens, so it is possible to bond the rod to the back of the body
In the case of Fujimi, the rear cowl is fixed .........
The rod was glued to the top of the partition in the room and the engineer room (((^ _ ^;)
DSC_9848





まだ仮にボディーを載せてるだけですが
F-40はカッコ良いですね
I still only temporarily put the body
F-40 is cool
DSC_9849




ボディーはデカール貼りですが
使うのはフェラーリのエンブレムぐらいですね
Although the body is decals
It is about the emblem of Ferrari to use
DSC_9850




シャシーはラジエターも付けたので終わりですね
The chassis also attached a radiator so it's over
DSC_9851





白のボディーに黄色のエンブレムは目立ちますね
The yellow emblem stands out on the white body
DSC_9852




このエントリーをはてなブックマークに追加 mixiチェック

5
sketch-1550879473290
フジミ 1/24 フェラーリ F-40 TOTIPを製作しています
We are manufacturing Fujimi 1/24 Ferrari F-40 TOTIP




前回クレオスのクリスタルカラーのサファイアブルーだと黄色味が強くなってしまったので
ガイアのパールシルバーに変更しました
The yellowish color has become stronger with the sapphire blue of Creos crystal color last time
It was changed to pearl silver of Gaia
DSC_9814




DSC_9815





line_1552222431672





黄色味は消えましたね
白っぽいパールホワイトになりました
光加減では少しシルバーぽくも見えますね
The yellowish color has disappeared
It became pale white pearl white
You can see a little silver Poku in light
DSC_9818





室内の組立ですが
シートは左右取り付けします
そして消火器は無しですね
レース仕様では無くて
乗用仕様です
It is assembly of the room
Seat attached to the left and right
And there is no fire extinguisher
It is not a race specification
It is a specification for riding
DSC_9840




エンジンの組立
接着は流し込みなので
これで一晩固定放置
Engine assembly
Because adhesion is pouring
It is fixed and left overnight
DSC_9841




次の日の昼です
マフラーやインタークーラー
エアクリーナー等の取り付けも終わりました
It is noon of the next day
Mufflers and intercoolers
Installation such as air cleaners was over, too
DSC_9842




室内はまだ仮に置いてるだけです
The room is only left temporarily
DSC_9843




このロッドの付く場所を確認したくて………
I want to check the location with this rod .........
DSC_9844


 


説明書を見るとこれだけの指示しか無いような………
エンジンルーム側はフレームの所何ですが相手は?………
Seeing the instructions only ... There is only this instrument ........ The engine room side is the place of the frame, but the other party? ...........
DSC_9845



このエントリーをはてなブックマークに追加 mixiチェック

5
Screenshot_20190413-233411



Screenshot_20190413-233434


今週は一万歩を超える日も有りました(^_^)

娘が小学校を卒業してからも
私は朝のウォーキングは続いてます
今週の水曜火が中学の入学式だったのですが
中学は小学校の登校時間より少しは遅いので
私は一人で寂しくですね(((^_^;)


ちなみに今朝は朝寝坊(;´∀`)
7時に起きてトイレに行ったのですが………
その後布団に戻ってしまった(゜ロ゜;ノ)ノ





このエントリーをはてなブックマークに追加 mixiチェック

↑このページのトップヘ