2019年03月
フジミ ディノ246GTエンスー後期型【31】
フジミ ディノ246GTエンスー後期型を製作しています
Fujimi Dino 246 GT Ensu is making late model
今回で完成です
前回から写真撮る余裕も有りませんでした(;´∀`)
本当に四苦八苦したと言うのが今の思いですね
It is completed this time
I had no time to take a picture from the last time (; '∀ `)
It is the present thought that it really struggled
ディノはまだ2キット有ります
エンスージアストの前期型と再販された前後期選択型と………
エッチングが1つしかなくて………
エンスーの前期に使い
前後期選択はエッチング無しでも良いかなと………
このディノは他の作業の合間にしてたのですが
去年の9月頃からしてまして(;´∀`)
完成したのも2月の11日でした
There are 2 kits yet for Dino
Early type of enthusiast and pre-late selective type resold ... ... ...
There is only one etching .........
Used during the previous term of Enzoo
I wonder if there is no etching for the preliminary or later term selection .........
This Dino was in between the other work
From around September of last year (; '∀ `)
It was also the 11th of February that I completed
明日からのアップ予定はアオシマのメルセデスベンツを予定してます
Scheduled to be up from tomorrow is scheduled for Aoshima's Mercedes Benz
ランキングに参加しています
ポチッと宜しくお願いします(^-^)v
フジミ ディノ246GTエンスー後期型【30】
フジミ ディノ246GTエンスー後期型を製作しています
Fujimi Dino 246 GT Ensu is making late model
力業を発動してます(((^_^;)
I'm activating my work force (((^ _ ^;)
最後になって合わない(((^_^;)
流し込みで接着してます(((^_^;)
It does not fit at the end (((_ _ ^;)
I'm gluing with pouring (((^ _ ^;)
スペアタイヤがボンネットに当たり
ボンネットが浮くのでスペアタイヤとホイール見えない面を削ってます
Spare tire hits bonnet
Since the hood floats, I am cutting spare tire and wheel invisible surface
タイヤを付けまして
センターのパーツはまだ付けてません
Have attached the tires
I have not attached parts of the center yet
ウォッシャータンクの位置ですが
説明書の所には付かないので
適当に付く場所に(((^_^;)
(実車は説明書の位置に付くみたいです)
It is the position of the washer tank
Because it does not stick to the instructions
Appropriate place to go (((^ _ ^;)
(The actual car seems to be attached to the position of the manual)
エンジンカウルはこれだけしか開きません(((^_^;)
何かミスをしたとかでは無いので(((^_^;)
(実車はもう少し開きますね)
The engine cowl opens only for this (((^ _ ^;)
It's not like I made some mistake (((^ _ ^;)
(The actual car opens a bit more)
ランキングに参加しています
ポチッと宜しくお願いします(^-^)v
ポチッと宜しくお願いします(^-^)v
模型・プラモデルランキング