2018年11月

5
sketch-1537021446195
フジミ フェラーリ 458 イタリアを製作しています
Fujimi Ferrari 458 I am producing Italy





最後に室内の写真を
ボディーを付けると見えなくなりますからね
Finally, I will post photos of the room
Because you will not be able to see it when you attach a body
DSC_7950




無事にボディーが付くのか?(゜ロ゜;ノ)ノ
一度リアのインナーフェンダー外れました(;´∀`)
再度接着してウォーキングへ行って
戻ってきてから付けました(^_^;)))
Is the body attached safely? (゜ ロ; ノ) ノ
Once the inner fender of the rear was disconnected (; '∀ `)
Adhere again and go to walking
I came back after it came (^ _ ^;)))
DSC_7949




合体が厳しいですね
インナーフェンダーが一度取れただけ済みましたが
外すのは勇気が要りますね(゜ロ゜;ノ)ノ
The coalescence is severe
I just finished the inner fender once
It takes courage to remove it (゜ ロ; ノ) ノ
DSC_7951




これで完成ですね
That's it.

黒背景だと色が変わっちゃいますね
The color changes when it is black background
DSC_7952




DSC_7953




DSC_7954




今回はピンク系の背景も撮ってみました
I also took a picture of the pink system this time
DSC_7956



DSC_7957




DSC_7964




DSC_7968




DSC_7969




DSC_7970




他のフェラーリと一緒に
With other Ferraris
DSC_7971




DSC_7972




DSC_7973


ガラスにグリーンの色を入れてますが
内装が黒いので判りませんね(^_^;)))

I put a green color on the glass
I do not understand because the interior is black (^ _ ^;)))




次回からはフジミのマクラーレンMP4-12C GT3を予定してます
このエントリーをはてなブックマークに追加 mixiチェック

5
先週は少しサボり気味ですね(゜ロ゜;ノ)

Screenshot_20181103-215025
寒くなって来て
朝6時過ぎに起きるのは辛くなって来ました(;>_<;)




今朝は起きましたよ\(^o^)/
昨日も少し早めに起きてたので
起きれたかな?(^_^;)))


なぜか今朝はGPSの調子も良かったので頑張りました\(^o^)/
Screenshot_20181104-074425


Screenshot_20181104-074437

う〜ん
これだけ歩いてもインスタントラーメン1つでチャラになってしまうんですよね(;>_<;)


このエントリーをはてなブックマークに追加 mixiチェック

5
sketch-1537021446195
フジミ フェラーリ 458 イタリアを製作しています
Fujimi Ferrari 458 I am producing Italy





いきなりライトが付いたりしてますが
ダークブラウンで墨入れしてあります
Suddenly the light is on
It is inked in dark brown
DSC_7935




ライトの横のメッシュ
Mesh next to the light
DSC_7936



フェンダーのメッシュ
Fender mesh
DSC_7937




こちらもフェンダーのメッシュ
Here is also a mesh of Fender
DSC_7938




リアフェンダーの上部のメッシュ
Mesh at the top of the rear fender
DSC_7939

比較的手軽に出来る所だけですが
メッシュに置き換え取り付けも終わりました

組み付けはしびれますね(((((゜゜;)
慌てずに少しずつですが確実に進めていきます

It is only a place that is relatively easy to do
Replaced with mesh The installation is over

Assembling is numb. (((((゜ °;)
Although it is not a panic but it gradually advances little by little



ミラーですが
盤面そのまま使っても良かったのですが
少しヒケが有るので削ったのですが
ミラーフィニッシュを貼るなら綺麗に
ツルツルにしとかないとダメなので………
Is it a mirror?
Although I could use the board as it was
I cut it because there is a little sink
If you put a mirror finish beautifully
Because it is useless if you do not get crawled out .........
DSC_7940




素材ごと変更しました
I changed each material
DSC_7941



これを切って使いました
I cut it and used it.
DSC_7942




DSC_7943




DSC_7944




フェンダーのウインカーは
インセクトピンの3番にメタルプライマーを塗ってクリアーオレンジを塗ってます
Fender's turn signal
I paint Clear Orange by applying Metal primer to Insect pin 3
DSC_7945





DSC_7946





DSC_7947




テールランプの付く所は
タミヤのペイントマーカーのシルバーで先に塗って有ります
Where the tail lamp is attached
It is painted in silver at the paint marker of Tamiya first
DSC_7948













このエントリーをはてなブックマークに追加 mixiチェック

5
sketch-1537021446195
フジミ フェラーリ 458 イタリアを製作しています
Fujimi Ferrari 458 I am producing Italy






コンパウンドのカスを綺麗に洗って
2〜3日放置してました(^_^;)))
特に意味は無いのですが
他のキットを少ししてました(^_^;)))
Wash the waste of the compound cleanly
I left it for 2-3 days (^ _ ^;)))
There is no particular meaning
I did a little other kit (^ _ ^;)))
DSC_7917





マスキング開始
Masking is started
line_1539260427202





出来ました
口で言えば簡単に終わったように思いますが……
時間は2時間ぐらい掛かったかな?(;´∀`)
it is complete
I think that it was easy to say by myself ... ...
Did it take about two hours? (; '∀ `)
DSC_7930




フロントの下側
マスキングするのが怖いのでしてません
絞って砂吹きで吹きます
Bottom of the front
I am afraid to mask, so I have not done it
Squeeze and blow with sand
DSC_7931




いきなり吹き終わり
マスキングも剥がしてます
砂吹きで吹いてますので
すぐに乾いてるので
すぐにマスキングをはずします
Suddenly blowing off
I am peeling masking as well
Because I'm blowing by the sand blow
Because it is dry soon
I will immediately remove masking
DSC_7932





絞って吹いてるとは言え
ミストが飛んでますので
エナメルシンナーで拭き取ってます
吹いてすぐならラッカーでもエナメルシンナーでも取れるの時が多いです
It is said that it blows squeezing
Because the mist is flying
I am wiping it off with enamel thinner
There are many times when you can bake lacquer or enamel thinner as soon as you blow it
DSC_7933




DSC_7934



このエントリーをはてなブックマークに追加 mixiチェック

5
sketch-1537021446195
フジミ フェラーリ 458 イタリアを製作しています
Fujimi Ferrari 458 I am producing Italy





クリアーを吹いてから5日放置してました
どんな状態か確認する為に天井を磨いてます
I left it for 5 days after blowing clear
I polish the ceiling to check what kind of condition it is
DSC_7900





セラミックまで掛けました
I hung it to ceramic
DSC_7901





ボンネットも磨いてます
I also polish the bonnet
DSC_7902





DSC_7904





DSC_7905





次の日の朝から
磨きの続きです
From the morning of the next day
It is a continuation of polishing
DSC_7906




DSC_7907





DSC_7908





DSC_7910





DSC_7911





そして昼に最終の磨きを
And finally polish at noon
DSC_7912




DSC_7913





DSC_7914





DSC_7915






DSC_7916

いったんコンパウンドのカスなどを綺麗にしてマスキングして行きたいと思います
窓枠と内側の塗装ですね
I think that I want to clean up the scum, etc. of the compound once and mask it
It's painted inside the window frame and inside


このエントリーをはてなブックマークに追加 mixiチェック

↑このページのトップヘ